How do I shut off my water heater?
Shutdown Instructions For The Hot Water Heater:
Step 1 – Turn Off the Gas Or Electricity power source
For a gas water heater, above the thermostat is a dial. Twist the thermostat dial to the OFF position. To cut the power to an electric power water heater, go to your circuit breaker box, locate the breaker to your water heater and switch it to the OFF position.
Step 2 – Turn Off The Water Supply
Turn the water shutoff valve clockwise until it stops. If this does not stop the water flow, then turn off the valve of the main water line to the house.
Step 3 – Drain Out The Water Heater
Attaching a hose to the drain valve of the water heater’s tank will allow you to remove all the water housed inside. The other end of the hose should be in a lower area at a safe location to dispense the water. Then to let air into the tank, open the hot water faucets in the house.
Step 4 – Open the relief valve on the hot water tank.
Position the handle straight out or up. Once the water finishes flowing from the hose, the tank is drained.
Be Careful! When the water coming out of the tank is still likely to be hot!
Why is the SEER rating on the Energy Guide different than what my dealer quoted?
Each split system cooling unit has a nominal SEER rating. This rating can be increased with the upgrade of the same series indoor unit. The SEER rating of a system is derived based on the combination of equipment installed in the home. The outdoor equipment (heat pump or air conditioner), as well as the indoor equipment (evaporator coil and furnace, or air handler), play a vital role in the total rating.
Why should I have regular (or preventative) maintenance? And how often should I have it performed?
Your heating and cooling systems work incredibly hard to perform their functions for your home everyday. The constant stopping, starting and continual operation can wear down any machine if the proper care and maintenance is delayed. However, by performing regular maintenance, you can maximize the lifecycle of your heating or cooling unit and guard against many common equipment failures. Preventive maintenance inspections performed on a regular basis can uncover leaks, rust, rot, soot, frayed wires and corroded electrical contacts that the naked eye may not notice. You should have maintenance done on your system regularly to ensure maximum efficiency and allow prevent possible problems that may occur in the near future.
What equipment requires regular (or preventative) maintenance?
At least twice a year heat pumps and air conditioners require a professional tune-up. Because gas-fired equipment functions with greater efficiency, they only need to be serviced every other year. Inspections on boiler and furnace systems should include ductwork, pipes, dampers, valves, the chimney, registers, radiators, pumps, blowers, fuel lines, the gas meter, oil tank and every part of the actual furnace and boiler. Meanwhile, heat pump and air conditioning unit inspections should also include inspections of the fan, compressor, indoor coils, outdoor coils, line kits and refrigerant lines.
I need help troubleshooting a problem with my equipment.
TemperaturePro is your troubleshooting expert, and is glad to help you. In addition, our partners also provide a network of troubleshooting technicians at Distribution centers across the country which TemperaturePro® will utilize to solve your concern. Should we encounter a situation that requires additional factory help, we will contact our factory supported Service Manager(s) for assistance.
What are the advantages of a programmable thermostat?
Since they are electronic, programmable thermostats are more accurate and efficient than thermostats that contain mercury. With programmable thermostats you can control the temperature in your home at different times of day without ever touching your thermostat. Because everything is automatic, you will never forget to change the setting on your own.
What type of filter should I use? And how often should I replace it?
Standard filters work to keep your system and its ductwork clean, but they don’t really improve indoor air quality. To do that you need a media filter. The media filter rests between the main return duct and the blower cabinet and will improve dust and particle removal by seven times that of a standard filter. However, upgrading to a pleated media filter will remove everything from insecticide dust to airborne viruses from the filtered air. Always choose a filter that matches your blower’s capacity. For optimum efficiency and filtration, TemperaturePro® recommends that you replace your disposable filters at least once a month. If you have washable filters, they should be cleaned once a month.
Why can’t I find the correct size furnace filter at my local home improvement store for my Brand Equipment?
The filter shipped with your unit is made from higher-quality materials than those of the disposable filters found in retail stores. For that reason, replacement filters can only be purchased through a dealer. However, keep in mind that some filters are reusable, and can be washed by hand in cold water.
Where can I get parts for my equipment?
As a dealer or multiple top-rated brands, TemperaturePro® is the best resource for identifying and supplying the correct, current parts for your system, as well as pricing and availability.
Which equipment will best fit my home?
There are many factors that affect the sizing and specifications of your system, including square footage, insulation, window surface and configuration, geographic location of your home, duct sizing and arrangement, and many others. TemperaturePro® can perform an in-home load analysis to determine which equipment combinations will perfectly suit your home and your family’s needs. Depending upon the construction of your home, one (1) ton of air conditioning can cool anywhere from 300 to 800 square feet of home. The only way to insure the size of the system you purchase will be large enough to cool your home, but not any larger than you need, is to have your home’s individual heating and cooling needs evaluated by a licensed professional.
What does my warranty cover?
Under the standard factory warranty, most manufacturers cover parts that fail during the warranty period due to defect in the part. The warranty does not cover labor. A warranty certificate was included with your homeowner information packet, and is specific to the model numbers, serial numbers and installation dates of your products. If you cannot find your warranty certificate, TemperaturePro® will also be able to provide you with the information.
What is the life expectancy of my unit?
Our partner brands dependable products are among the longest lasting heating and cooling products available. For your specific equipment, there are many variables that affect life expectancy, and of course, the regularity of routine maintenance.